Made to order
UltiMaker PVA Removal Station – Dissolve PVA Supports up to 4× Faster
Automated support-removal station that dissolves PVA up to 4× faster than motionless water — magnetic rotor circulation, an illuminated tank, and a lift-out rinsing basket for hands-off post-processing.
- ✓ Up to 4× faster PVA removal — cuts operator time up to 80%
- ✓ 200 × 230 × 165 mm basket · 13.7 L illuminated tank with saturation indicator
- ✓ Genuine UltiMaker hardware — made to order, typical lead time 1–2 weeks
$1,095
Built for unattended post-processing
Up to 4× faster, hands-off
A magnetic rotor circulates water into every cavity, dissolving PVA up to 4× faster than motionless soaking and cutting operator time by up to 80%. Set 225 or 100 RPM by part fragility, press start, and walk away.
An applications engineer on the line
Questions on PVA handling, dual-extrusion support settings, or cycle times? Our engineers run these post-processing workflows in-house — sub-4h reply, NDA standard.
The UltiMaker PVA Removal Station automates support removal for dual-extrusion FFF prints. A magnetic rotor circulates water around the part to dissolve PVA supports up to 4× faster than soaking in a motionless container — with only a few minutes of operator time per print.
What the PVA Removal Station Does
PVA (polyvinyl alcohol) is a water-soluble support material printed alongside models in PLA, Tough PLA, Nylon, PETG or CPE on dual-extrusion systems. The UltiMaker PVA Removal Station dissolves that support automatically: load the part into the rinsing basket, press start, and collect a finished print — no manual scrubbing and minimal maintenance. It reduces operator time by up to 80% compared with hand-tended soaking.
Rotor-Powered Water Circulation
A magnetic rotor drives high-speed circulation that reaches into cavities and lattices motionless water never clears. Choose 225 RPM (normal) or 100 RPM (low) depending on part fragility; every two minutes the rotor reverses direction to push water evenly across the model. See full specifications below.
Prints Stay Safe and Submerged
The rinsing basket (200 × 230 × 165 mm) holds the print fully submerged in the 13.7-liter tank while dissolving, then lifts out for mess-free draining and removal — no reaching into solution.
Easy to Monitor
A transparent, illuminated tank lets you watch removal progress, and a saturation indicator shows when to refresh the water so dissolving stays fast.
Why Source Through Additive Plus
Genuine UltiMaker hardware, stocked and supported in the US. Our engineers run these post-processing workflows in-house and can help you match materials, cycle settings, and PVA handling to your parts, with a response in under 24 hours.
| Brand | UltiMaker |
| Container volume | 13.7 liters (3.6 US gal) |
| Maximum part size | W 200 x D 230 x H 165 mm (W 7.8 x D 9 x H 6.4 in) |
| Supported materials | Optimized for: PLA and PVA Also suitable for: PETG, Tough PLA, Nylon, or CPE in combination with PVA (Also supports equivalent third-party materials) |
| Technology | FFF |
| Rotor speed | 225 RPM (normal) 100 RPM (low) |
| Operating ambient temperature | 15 - 32 °C (59 - 90 °F) |
| Power Consumption | 38 W |
Other products teams run alongside UltiMaker PVA Removal Station – Dissolve PVA Supports up to 4× Faster
In stock
Replacement activated-carbon air filters for the Nexa3D XiP Pro. They capture resin odour and VOCs from the printer's airflow, keeping the enclosure and production floor cleaner. Swap them on schedule to maintain filtration.
- ✓ Activated-carbon odour / VOC capture
- ✓ Sized for the Nexa3D XiP Pro (not the standard XiP)
- ✓ Genuine Nexa3D consumable · ships in 2 business days
In stock
· 2 Business Days
Zetasinter Chamber sinters printed ceramic parts in ambient air, up to 1600 °C.
- ✔ Sinters in ambient air — no gas supply, no atmosphere control to manage
- ✔ 1600 °C maximum: alumina at 1550 °C, white and black zirconia at 1475 °C
- ✔ 250 × 250 × 250 mm chamber takes real parts, not only test pieces
Freight and installation requirements confirmed with you before the order is placed.
Made to order
· Ships from California · timeline confirmed at quotation
In stock
· 1–2 Business Days
In stock
In stock
In stock
Genuine Sygnis UV module for the F-NIS 3D printer — 365 nm and 405 nm post-processor-controlled diodes that upgrade the machine from version A to version B.
- ✓ Dual-wavelength: 365 nm + 405 nm UV curing
- ✓ Post-processor-controlled diodes — self-installed A→B upgrade
- ✓ In stock — ships in 2 business days from US inventory
In stock
· 2 Business DaysCommon questions
Don't see yours? Email [email protected] — NDA standard, typical reply within 4 hours.
Which printers and materials does the PVA Removal Station work with?
How much faster is it than dissolving PVA in a container of water?
How much operator time does it need?
What are the tank and basket dimensions?
Do I need to heat the water or add chemicals?
Place your order, or talk to an engineer first
Order UltiMaker PVA Removal Station – Dissolve PVA Supports up to 4× Faster direct, or talk to materials engineer