Tailored Warranty And Support
Financing Available Today

Metal Powder for LPBF: How to Check Compatibility Before Buying

Buying metal powder for a laser powder bed fusion (LPBF) printer is not like buying a commodity. The same alloy name can hide different particle size distributions, oxygen levels and flow behavior, and any of these can change how a build runs. This guide lists what to check before you order, so you can match a powder to your machine and parameter set instead of finding problems after the first build.

What “LPBF-compatible” does and does not mean

Be clear on one point first. Powders we list as LPBF-compatible are sold for use in laser powder bed fusion. That is not the same as being approved or qualified by a printer manufacturer. We do not claim OEM approval for any powder, and a product label cannot guarantee how it will run on your specific system.

Compatibility has to be verified for each machine. Gather your printer model, your parameter set and your target alloy, and compare them with the powder specification before you commit to a lot. If you need a qualified material for a regulated part, your own qualification process still applies.

1. Particle size distribution and layer thickness

Particle size distribution (PSD) is the first filter. Most LPBF powders are supplied in a range such as 15–45 µm or 15–53 µm. Aluminum is often supplied at 20–63 µm. The range should fit the layer thickness your parameters use:

  • Upper end of the range: coarse particles can be comparable to the layer thickness. That can cause recoater streaking or uneven spreading, especially at thin layers.
  • Lower end of the range: very fine particles raise the risk of agglomeration, poor flow and higher surface area for oxygen and moisture pick-up.
  • Your parameter set: parameters are developed around a specific distribution. A noticeably different PSD may call for re-optimization, even when the alloy is identical.

Ask whether measured D10, D50 and D90 values are available for the lot, not just the nominal range. The range tells you the sieve cuts. The percentiles tell you what is actually in the container.

2. Chemistry and the specification it follows

Confirm that the alloy grade matches the standard your part drawing or process specification calls for. Check the elemental limits, not only the name. “316L” and “Ti-6Al-4V” each cover several variants. For titanium, Grade 5 and Grade 23 (ELI) differ in interstitial limits, and ELI is the usual choice where lower oxygen is wanted for ductility and toughness.

Ask what chemistry documentation, such as a certificate of analysis (COA), is available for the lot you would receive. Compare it with your required limits before you buy, not after the powder is on site.

3. Flowability and apparent density

A powder that does not spread evenly produces uneven layers, whatever the laser settings. The usual indicators are flow rate (for example Hall or Carney funnel tests), apparent density and tap density. Powders at the fine end of the PSD may not flow through a standard funnel at all, so a no-flow result does not by itself mean the powder will fail on the recoater. Dynamic methods can fill that gap. Whichever method you use, compare like with like: the same test on the same powder condition, ideally dried.

Flowability and characterization methods deserve a deeper treatment of their own. Here the practical point is to ask which tests were run and under what conditions, so you can compare a new lot with a powder that already runs well on your machine.

4. Oxygen, nitrogen, hydrogen and moisture

Interstitial content affects both the powder and the finished part. Oxygen matters for titanium and for aluminum. Check any gas analysis against the limits in your specification. Also consider handling:

  • Powder picks up moisture. Humidity can hurt flow and increase porosity risk.
  • Reused powder tends to gain oxygen over repeated builds. Track it with a sampling plan rather than assuming it stays constant.
  • Store opened containers sealed and dry, and follow the safety practice that applies to reactive materials such as aluminum and titanium powders.

5. Process gas and machine setup

Check which inert gas your machine and parameter set are designed for. Argon is the common choice across materials. Nitrogen is used for some alloys on some systems, but it is generally not suitable for titanium because of nitrogen pick-up. Also check:

  • The sieving setup and mesh size used in your powder handling loop
  • The recoater type (blade, brush or other), which responds differently to powder flow
  • The build plate material and preheating, if the alloy needs it

A quick comparison from our catalog

The three LPBF powders below show how PSD, origin and price differ across common alloys. Prices are per 10 kg unit, with the per-kg figure calculated from that.

Powder Maker Particle size Price per 10 kg Price per kg Availability
316L stainless steel Carpenter Additive (Sweden) 15–45 µm $680 $68.00 In US stock · ready to ship
AlSi10Mg aluminum Carpenter Additive (Austria) 20–63 µm $830 $83.00 In US stock · ready to ship
Ti64 Grade 23 (ELI) titanium Amaero (USA) 15–53 µm, 20–75 µm $2,405 $240.50 In US stock · ready to ship

Note that the titanium listing includes two size ranges. If you choose it, check which range you need against your layer thickness and recoater setup, and confirm the range with us before ordering.

A pre-purchase checklist

  1. Write down your machine model, layer thickness, gas and current parameter set.
  2. Define the alloy grade and specification you need to meet.
  3. Compare the powder’s PSD range, and the D10/D50/D90 values if available, against your parameters.
  4. Review the available documentation for chemistry and oxygen, nitrogen and hydrogen content.
  5. Ask which flowability and density tests were run, and under what conditions.
  6. Confirm availability and lead time, then plan a small first lot or test build before scaling up.

If you are comparing alloys or size ranges, the full metal powders category lists what we carry, including the particle size range on each listing.

Start with a small validation

Even with matching specifications, run a validation build with a new powder before you commit it to production. Check density, surface finish and mechanical properties against your acceptance criteria. Keep the lot records so you can trace any change in behavior back to the powder or to the process.

Questions before you order

If you have questions about pricing, available documentation or a specific size range, contact us with your printer model, alloy and layer thickness. We will tell you what we can confirm about the listing; final compatibility with your machine remains something to verify with a validation build.

Talk to an engineer

Have a question or a project? Let’s talk.

Tell us what you need — a real applications engineer replies within 24 hours. NDA on request, no sales script.