Slurry
Slurry-based ceramic 3D printers — stereolithography systems that cure ceramic slurry layer by layer for high-resolution, high-density parts in materials like alumina and zirconia. Suited to precision technical-ceramic components for thermal, wear, and electrical applications. Compare printers by build size, resolution, and material range.
Industrial laser SLA ceramic 3D printer built for serial production — a 12.6×12.6×7.9 in / 320×320×200 mm build, one- or two-laser configuration, and CERIA process automation. Runs alumina, zirconia, silicon nitride, AlN, HA and more, with the full print → debind → sinter workflow supported by Additive Plus.
- 320×320×200 mm build — UV laser 300 mW, ~60 µm spot, one or two lasers.
- 7+ technical ceramics — alumina, zirconia, Si₃N₄, AlN, hydroxyapatite, TCP, cordierite.
- Lead time: configured to order — install, training & debind/sinter support from California.
Made to order
· Lead time: configured to order — request a build slot. Installation, training and process support included from California.
Compact open-parameter ceramic SLA printer for research and material development — a 3.9×3.9×5.9 in / 100×100×150 mm build that starts a print from as little as 60 mL of ceramic. Develop your own process, then scale the same technology to 3DCeram production systems. Full print → debind → sinter workflow supported by Additive Plus.
- Open parameters — qualify new ceramics & formulations, not just vendor recipes.
- Print from 60 mL — 10 mL with SAM option · change ceramic in ~20 min.
- Lead time: configured to order — install, training & scale-up support from California.
Made to order
· Lead time: configured to order — request a build slot. Installation, training and process support included from California.
Multi-material ceramic SLA printer that prints two materials in the same layer — ceramic plus a second ceramic, metal or polymer — on a 3.9×3.9×5.9 in / 100×100×150 mm platform. It makes functionally graded and multi-material ceramic parts single-material printing can't. Full print → debind → co-sinter workflow supported by Additive Plus.
- Two materials in one layer — ceramic + ceramic, metal or polymer.
- Open-parameter R&D — 100×100×150 mm build, cartridges from 60 mL.
- Lead time: configured to order — material-pair & co-sinter support from California.
Made to order
· Lead time: configured to order — request a build slot. Installation, training and process support included from California.
Production-scale multi-material ceramic SLA system: alongside the base ceramic it deposits up to three additional materials in one part, via dispensers from needle valve to micro-distribution, all in CPS 2.0. On an 11.8×11.8×3.9 in / 300×300×100 mm platform with a fine 35 µm UV laser. Full print → debind → co-sinter workflow supported by Additive Plus.
- Up to 4 materials in one part — base ceramic + 3 dispensed materials.
- Fine 35 µm UV laser — 355 nm, detail across the 300×300 mm platform.
- Lead time: configured to order — material-set & co-sinter support from California.
Made to order
· Lead time: configured to order — request a build slot. Installation, training and process support included from California.
Quad-laser SLA ceramic 3D printer for serial production — a 600×600×300 mm build envelope, four 405 nm UV lasers, and an open architecture that runs any qualified ceramic paste.
- ✓ Largest plate in the 3DCeram line — 600×600×300 mm (23.6×23.6×11.8 in)
- ✓ Support-free top-down SLA · surface roughness under 2 µm
- ✓ Lead time: configured to order — full print → debind → sinter workflow supported
Made to order
· Built to order — contact us for the current lead time and installation schedule.
Compact ceramic SLA printer for small-series production of technical-ceramic parts — a 3.9×3.9×5.9 in / 100×100×150 mm build that starts a print from as little as 60 mL of ceramic. A peristaltic pump and pressurized tank hold a stable slurry flow for repeatable parts, and the same process scales up to 3DCeram production systems. Full print → debind → sinter workflow supported by Additive Plus.
- Built for small series — repeatable ceramic parts, not one-off prototypes.
- Print from 60 mL — 10 mL with SAM option · change ceramic in ~20 min.
- Lead time: configured to order — install, training & scale-up support from California.
Made to order
· Lead time: configured to order — request a build slot. Installation, training and process support included from California.
- ✓ 11+ ceramic materials — Al₂O₃, ZrO₂, Si₃N₄, TCP, HA, AlN, cordierite and more
- ✓ Top-down SLA — support-free complex internal geometries in dense ceramic
- ✓ SAM option — 100 mL minimum batch for R&D economy with expensive compositions
Made to order
· Configured to order — contact for lead timeNot sure which system fits?
Tell us your application. We'll send our top recommendation.
Browse all categories
Printers, materials, print services and lab equipment — including AO Metal, the LPBF printer we design and build ourselves.
Have a CAD? Have a quote in 24h.
Upload your file or talk to an engineer — no obligation, no spam, NDA on request. First-time customers get free DfAM review.