Out of stock
- SDS + technical datasheet linked on every order — no separate request needed
- No HazMat shipping — ships standard ground, no Dangerous Goods surcharge
Nexa3D xCLEAN parts washing solution, 1 liter
Currently not in stock. Leave a request and we will confirm availability, price and lead time.
Nexa3D xCLEAN parts-washing solvent — 3x IPA's saturation limit, no HazMat shipping, clears photopolymer resin residue in about 5 minutes.- ✓ 3x IPA's saturation limit — fewer bath changeovers
- ✓ Not a Dangerous Good at this size — ships without HazMat freight
- ✓ available on request (not in stock)
$24
What your process engineer actually checks
3x IPA's saturation limit, before you change the bath
xCLEAN holds roughly three times the resin-saturation capacity of isopropyl alcohol before the wash bath needs replacing — fewer changeovers, less spent solvent to dispose of. It rinses clean in water and leaves none of the greasy residue typical of TPM or DPM.
No HazMat shipping, no ATEX cabinet
xCLEAN is not classified as a Dangerous Good under IATA or EU transport rules at these order sizes, so it ships without hazardous-freight surcharges and doesn't require ATEX-rated storage the way some resin solvents do. It's still a combustible liquid — keep it capped, away from heat and open flame.
A materials engineer on the line
Questions on resin compatibility, wash-cycle time, or whether your automated washer handles xCLEAN? A materials engineer answers directly — most replies in under 4 hours, NDA standard.
xCLEAN is Nexa3D’s dedicated parts-washing solvent for photopolymer resin prints — a 2-butoxyethanol-based formulation built to replace IPA, TPM, and DPM in the wash station, not another version of them.
Why process engineers switch from IPA to xCLEAN
Spec-backed differences, not marketing claims
3x IPA’s saturation limit
A liter of xCLEAN holds roughly three times the resin load isopropyl alcohol can before the bath needs changing — fewer changeovers, less spent solvent.
Rinses clean, no greasy film
Made from smaller molecules than TPM or DPM. Parts rinse clean in water instead of carrying the greasy residue those solvents leave behind.
No HazMat shipping
Not classified as a Dangerous Good under IATA or EU rules at these order sizes — it ships without hazardous-freight surcharges or special paperwork.
Recoverable by distillation
Recycle and recover xCLEAN with a vacuum-assist solvent distillation unit, extending working life well past a single wash cycle.
Wash
Agitate or ultrasonic-wash printed parts in xCLEAN — uncured resin typically clears in about 5 minutes.
Rinse
Rinse in water. No greasy TPM/DPM film to wipe down afterward.
Recover
Once saturation nears the practical limit, recover xCLEAN with vacuum-assist distillation instead of disposing of the full bath.
Chemical & Safety Specifications
| Property | Value |
|---|---|
| Primary component | 2-Butoxyethanol, >98% (CAS 111-76-2) |
| Physical state / color | Liquid, colorless, mild sweet/ester odor |
| Specific gravity (20°C) | 0.90 g/cm³ |
| Dynamic viscosity (20°C) | 3.3 mPa·s |
| Flash point (closed cup) | 67°C |
| Boiling point | 171°C |
| Solubility in water | 900 g/L (25°C) — rinses off in water |
| GHS classification | Combustible liquid (H227); harmful if swallowed/inhaled; skin & eye irritant; may cause drowsiness |
| Transport (DOT/IATA) | Not regulated as a Dangerous Good below 450 L (119 gal) — ships without HazMat surcharge |
Full hazard statements, handling, and PPE guidance are in the Safety Data Sheet — see Downloads below.
Compatibility
- Works across most photopolymer resin systems — not limited to Nexa3D’s own resins or printers.
- Compatible with most automated and closed-loop washing units on the market, including Nexa3D’s Wash+Cure station.
- Not approved for cleaning parts printed from biocompatible resins — follow the resin manufacturer’s wash guidance for those applications.
Typical applications
Not sure 1 liter is the right size for your throughput? Same chemistry, larger volumes:
Tell us your wash volume and equipment — a materials engineer will recommend the right size and cycle settings.
Why Source Through Additive Plus
- Authorized Nexa3D reseller — genuine xCLEAN, available on request.
- A materials engineer answers compatibility and wash-cycle questions — most replies in under 4 hours.
- Stock the size that matches your throughput: 1 L, 5 L, or 5 gal, same chemistry, no reformulation risk.
| Brand | Nexa3D |
| Weight | 1000 ml |
| Country of origin | USA |
| Printing Materials | Other Materials |
| Platform | XiP |
| Technology | LSPc, DLP, XiP |
| Application | Engineering, Manufacturing |
Product videos
Step up to 5 liters or 5 gallons — same xCLEAN, lower cost per liter.
Production teams save on a per-liter basis at the 5-liter and 5-gallon sizes — same formulation, no requalification. Compare sizes above, or ask a materials engineer which fits your wash-cycle volume.
Complete the workflow
All-in-one desktop wash and post-cure station for parts printed on the Nexa3D XiP.
- ✓ 5.5 L sealed wash bucket with a basket that takes the XiP build plate whole
- ✓ Magnetic stirring, runs on xCLEAN or isopropanol
- ✓ 405 nm LED cure tower with rotating base and reflector hood
- ✓ Ships in 2 business days from US stock
Replacement resin vat for the Nexa3D XiP — the tray that holds resin over the masking LCD and carries the membrane the print peels from each layer. As the membrane clouds or wears, print quality drops; a fresh vat restores clean, consistent layers.
- ✓ Resin vat assembly for the XiP LSPc engine
- ✓ Direct fit for the Nexa3D XiP desktop printer
- ✓ Genuine Nexa3D part · ships in 2 business days
The genuine Nexa3D Everlast-2 membrane keeps your XiP producing clean, consistent parts — print after print.
- ✔ Rated 50,000+ layers (~20 L per membrane) — up to 25× the life of standard films
- ✔ Genuine Nexa3D OEM — second-generation interface for sharp feature definition
- ✔ Ships from our Los Angeles warehouse in 5–15 business days
Order a spare today — a worn membrane shouldn’t cost you a print day.
Other products teams run alongside Nexa3D xCLEAN parts washing solution, 1 liter
CNPC Ti-6Al-4V Grade 23 ELI powder for LPBF — made by CNPC Powder, argon gas-atomized, 15–53 µm, sold in 10 kg containers.
- 10 kg container · $136/kg · $1,360
- Certificate of analysis (COA) for the lot, on request
- In stock in California — ships within 2 business days
Manufacturer: CNPC Powder · materials engineer on call · order below or talk to an engineer first.
In stock
· In stock in California · ships within 2 business days
In stock
· 1–2 Business Days
Hot-bath cleaning liquid that removes uncured resin from demanding SLA/DLP parts at temperatures up to 80 °C — formulated to avoid peroxide generation when heated.
- ✓ Runs hot to 80 °C safely — no peroxide formation
- ✓ For high-temperature and FST resins (e.g. Loctite 3955 HDT280 FST)
- ✓ 18 kg · in stock — ships same day
In stock
· Ships same day from Los Angeles
Versatile. Weldable. Cost-effective. Genuine Carpenter PowderRange® 304 / 304L austenitic stainless steel for LPBF & EBM metal 3D printing.
- ✓ Gas-atomized, low-oxygen — COA on request
- ✓ Sold in small, workable volumes — no large mill minimums
- ✓ In US stock — ready to ship
In stock
· In US stock · ready to ship
Two genuine Nexa3D Everlast-1 membranes for the XiP Pro — a backup always ready.
- ✔ Each rated 50,000+ layers (~20 L) — up to 25× the life of standard films
- ✔ Lower cost per membrane than singles — genuine Nexa3D OEM
- ✔ Ships fast from our Los Angeles warehouse — lead time 5–15 business days
Never lose a production day to a worn membrane and an empty shelf.
In stock
· 5–15 Business Days
In stock
· 1–2 Business Days
Currently not in stock. Leave a request and we will confirm availability, price and lead time.
Bulk washing solvent for rinsing uncured resin off SLA and LSPc 3D-printed parts — holds around 3× the dissolved resin of IPA and has a higher flash point, in a 5-gallon pack that lowers cost per litre for production.
- ✓ ~3× the resin capacity of IPA — fewer changeouts, less waste
- ✓ Higher flash point than IPA · leaves no greasy residue · water-rinse after
- ✓ 5 gallon (18.9 L) · US-made · available on request (not in stock)
Out of stock
· Not in stock — available on request
In stock
· Express 2–3 wks · Standard 6–8 wksCommon questions
Don't see yours? Email [email protected] — NDA standard, typical reply within 4 hours.
What is Nexa3D xCLEAN and how is it different from isopropyl alcohol (IPA)?
Which resins and 3D printers is xCLEAN compatible with?
Does xCLEAN require special shipping or storage like other resin-cleaning solvents?
How long does a wash cycle take with xCLEAN?
Can xCLEAN be recycled or reused?
What size should I order — 1 liter, 5 liters, or 5 gallons?
Is xCLEAN safe to handle, and what PPE does it require?
Do you offer a purchase order or volume pricing for xCLEAN?
Place your order, or talk to an engineer first
Order Nexa3D xCLEAN parts washing solution, 1 liter direct, or talk to materials engineer