In stock
- Debind & sinter parameters + datasheet in every order
- Mutual NDA before any file or spec review
Fila-MAT Metal Titanium 1,75mm
- ✔ Rp0.2 844 MPa, Rm 940 MPa at 4.33 g/cc after sintering — tested to ASTM E8/E8M
- ✔ Debind and sinter parameters plus the full datasheet included with every spool
- ✔ 1.75mm bound-metal feedstock for the 3DCeram M.A.T. FFF head — mutual NDA before any spec review
What your process engineer actually checks
Third-party mechanical data
Rp0.2 844 MPa, Rm 940 MPa at 4.33 g/cc density and a 118 GPa modulus after sintering, tested to ASTM E8/E8M. You qualify Fila-MAT Metal Titanium against measured numbers, not a filament-vendor estimate.
Debind and sinter parameters included
Every spool ships with 3DCeram's datasheet and the full print, debind and sinter cycle for the M.A.T. FFF head, so green parts reach target density on the first build instead of after trial-and-error.
A materials engineer on the line
Shrinkage, warpage and heat-treatment questions go to an engineer who has run bound-metal FFF — not a ticket queue. Sub-4h reply, mutual NDA on request before any spec review.
Fila-MAT Metal Titanium is 3DCeram’s bound-metal FFF feedstock — 1.75mm filament loaded with Ti6Al4V (Grade 5) titanium powder for the M.A.T. multi-head extrusion printer. Print the green part on a standard FFF head, then debind and sinter to a dense, high-strength, lightweight titanium component.
Why engineers choose Fila-MAT Titanium
Four things a process engineer checks before qualifying a bound-metal feedstock.
844 MPa yield, 940 MPa tensile
Rp0.2 844 MPa / Rm 940 MPa post-sinter, tested to ASTM E8/E8M — Ti6Al4V (Grade 5) performance, not a filament-vendor estimate.
4.33 g/cc — lightweight alloy
Low-density titanium at 4.33 g/cc — high strength-to-weight for aerospace and lightweight structures.
Tested at ESA’s ESTEC facility
Mechanical data measured with calibrated equipment at the European Space Agency’s technology centre in the Netherlands — third-party test conditions.
Debind & sinter parameters included
Every spool ships with 3DCeram’s datasheet and process parameters for the M.A.T. FFF head, so green parts reach target density predictably.
How the Fila-MAT workflow runs
Print, debind, sinter — the same three-step process behind every bound-metal FFF part.
Print on the M.A.T. FFF head
1.75mm feedstock runs on 3DCeram’s M.A.T. printer — max nozzle 270°C, max bed 110°C, with heated filament and print chambers for consistent extrusion.
Debind the binder
Binder-removal parameters ship with every spool’s datasheet, tuned for the titanium feedstock — no trial-and-error on the first batch.
Sinter to dense metal
High-temperature sintering consolidates the part to dense Ti6Al4V — ready for use or optional stress-relief.
Material properties (post-sinter)
| Property | Value | Standard |
|---|---|---|
| Density | 4.33 g/cc | — |
| Yield strength, Rp0.2 | 844 MPa | ASTM E8/E8M |
| Ultimate tensile strength, Rm | 940 MPa | ASTM E8/E8M |
Tested with calibrated equipment at ESA’s ESTEC technology centre, Netherlands. See the full datasheet in Downloads.
Technical specifications
- Material: Ti6Al4V (Grade 5) titanium alloy, bound-metal FFF feedstock
- Filament diameter: 1.75mm
- Compatible platform: 3DCeram M.A.T. — FFF head, max nozzle 270°C, max bed 110°C, filament chamber ≤50°C, print chamber ≤50–60°C
- Post-processing required: chemical/thermal debind + sinter furnace — parameters supplied with the datasheet on every order
Typical applications
Where teams run Fila-MAT Titanium today.
Not sure Fila-MAT Titanium is the right fit?
Three reasons teams pick a different feedstock or platform — tap the closest match.
Why source Fila-MAT through Additive Plus
- 3DCeram-qualified feedstock for the M.A.T. FFF head — matched to the machine, not a generic substitute.
- Debind and sinter parameters plus full datasheet included with every order.
- Materials engineer on the line for shrinkage, warpage, and heat-treatment questions — NDA on request.
- Custom alloy or ceramic feedstock sourced and qualified on request, typical lead 3–4 weeks.
| Brand | 3DCeram |
| Printing Materials | Metal Filaments |
| Technology | FFF |
| Application | Composite Tooling, Engineering, Jigs & Fixtures, Manufacturing |
Product videos
We source and qualify. Custom feedstock on request.
Complete the workflow
Metal & technical ceramics, printed by extrusion — even silicon carbide.
- FFF · pellet · paste + 3-axis CNC in one machine
- No laser, no loose powder — lab-safe, single-phase
- Official 3DCeram US representative · 12-mo warranty
From $63,100 · Core: FFF + CNC (add Pellet/Paste heads) · made to order, ~3-month build · leasing available
Request a quote Installation and commissioning in the USA: facility and gas planning, start-up and operator training by our US service team.
Controlled atmosphere oven for metal AM post-processing and materials research — 400–700°C max (4 grades), 28–1,000 L chambers (5 sizes), O₂ down to 50 ppm with N₂/Ar purge. Seam-welded gas-tight chamber built as an atmosphere unit from the ground up.
- ✓ O₂ down to 50 ppm — atmosphere-controlled heat treatment without vacuum-furnace cost
- ✓ 17 configurations in one family — 28 L lab to 1,000 L production, same gas architecture
- ✓ Seam-welded gas-tight chamber — purpose-built, not a retort-converted standard oven
- ✓ Configured to order — request lead time; install, training & cycle validation included
- ✔ Rp0.2 680 MPa / Rm 880 MPa / 257 HV10 — tested to DIN EN ISO 6892 & 6507-1 at ESA's ESTEC facility
- ✔ Debind & sinter parameters plus full datasheet included with every spool
- ✔ 1.75mm bound-metal feedstock for the 3DCeram M.A.T. FFF head — mutual NDA before any spec review
Other products teams run alongside Fila-MAT Metal Titanium 1,75mm
Lightweight. Thermally conductive. Heat-treatable. Genuine Carpenter PowderRange® AlSi10Mg aluminum alloy for LPBF metal 3D printing.
- ✓ Gas-atomized — COA on request (20–63 µm, 10 kg = 2 × 5 kg containers)
- ✓ Sold in small, workable volumes — no large mill minimums
- ✓ In US stock — ready to ship
In stock
· In US stock · ready to ship
- ✔ Excellent corrosion resistance, ductile and well suited to functional parts
- ✔ Print → debind → sinter to dense 316L on a desktop FFF printer
- ✔ Genuine Zetamix by Nanoe · 500 g spool · lead time 10–20 business days (depending on order queue)
In stock
· Ships in 1–2 business days
Made to order
· Express 2–3 wks · Standard 6–8 wks
Need a HIPed titanium build platform for a different printer model or custom dimensions? Request a custom quote — we manufacture precision HIPed titanium build plates and additive manufacturing platforms for most metal AM systems.
Other materials available upon request.Made to order
· 4-5 weeks
ASA filament for FDM 3D printing — ABS-grade strength with the UV, weather, and color stability sunlight doesn't fade, plus a 90°C HDT for outdoor housings, automotive exterior parts, and signage.
- ✓ ±0.02mm diameter tolerance — consistent extrusion, low jam risk
- ✓ Validated CreatBot F430 print profile + datasheet included
- ✓ In stock, ships in 1–2 business days
In stock
- ✔ Smooth, glazeable porcelain finish with a classic ceramic look
- ✔ Print → debind → fire — ceramic printing on an everyday FFF machine
- ✔ Genuine Zetamix by Nanoe · 500 g spool · lead time 10–20 business days (depending on order queue)
In stock
· Ships in 1–2 business days
- ✓ ESA/ESTEC-verified: 423 MPa flexural strength, 82 W/m-K thermal conductivity
- ✓ Solid-state sintered to 2100°C — dense, chemically inert, no powder bed
- ✓ Qualified for the 3DCeram M.A.T. platform — quote-based pricing, request a quote
In stock
· Contact for lead time
HDT115°C black resin: Precision molds, intricate heat-resistant parts. Low viscosity.
Availability: confirmed at order. Supplier stock for this line varies — we verify availability and lead time on every order before processing, and offer an equivalent or a full refund if an item cannot be supplied. Cubic Ink equivalents →
Made to order
· Ships in about 2 weeks — final date confirmed after you orderWhat our customers say
“Harry and team were professional, effective communicators as we set up the order, then they executed quickly and produced an amazing product for us at a very competitive price. Am looking forward to our next print w Additive Plus!”
“Great 3D printing service and the resin parts look super smooth and clean. Really happy with how everything turned out!”
“Harry was very professional and helped me out with my 3D printing needs and explained what options I have in terms of filaments such as PEEK. Highly recommended.”
“I needed a 3D enclosure printed urgently in a specific time period, they did great!”
Common questions
Don't see yours? Email [email protected] — NDA on request, typical reply within 4 hours.
What is Fila-MAT Metal Titanium and how does it produce metal parts?
Which printer is Fila-MAT Metal Titanium compatible with?
What post-processing does Fila-MAT Metal Titanium require?
What mechanical properties can I expect after sintering?
How much does a Fila-MAT Metal Titanium part shrink during debinding and sintering?
Why print titanium with bound-metal FFF?
Does Fila-MAT Metal Titanium need special sintering?
Place your order, or talk to an engineer first
Order Fila-MAT Metal Titanium 1,75mm direct, or talk to materials engineer