Equipment
Cast your own feedstock rods for ATO atomizers — from any alloy you design or from AM scrap — with pre-melt purification and induction melting under vacuum.
- Built-in resistance furnace purifies the charge before casting
- 120 mm rods for the Revolver Rod Feeding System · re-cast AM scrap
- Installation, training and US service included · free powder samples
- Lead time 8–12 weeks · 12-month warranty
Made to order
· Lead time 8–12 weeks · installation included
Automated cleaning system that removes excess ceramic paste from freshly printed green parts, leaving them ready to debind — replacing slow, hands-on solvent cleaning in the ceramic AM workflow.
- ✓ Gentle, low-mechanical-stress cleaning of fragile green parts
- ✓ Batch time cut dramatically vs manual (e.g. 60 min → 5 min on 70 alumina parts)
- ✓ Solvent longevity + recycling · no manual solvent contact
In stock
· Lead time, utilities and installation confirmed at quote — configured to order. Install and training included.
Industrial laser SLA ceramic 3D printer built for serial production — a 12.6×12.6×7.9 in / 320×320×200 mm build, one- or two-laser configuration, and CERIA process automation. Runs alumina, zirconia, silicon nitride, AlN, HA and more, with the full print → debind → sinter workflow supported by Additive Plus.
- 320×320×200 mm build — UV laser 300 mW, ~60 µm spot, one or two lasers.
- 7+ technical ceramics — alumina, zirconia, Si₃N₄, AlN, hydroxyapatite, TCP, cordierite.
- Lead time: configured to order — install, training & debind/sinter support from California.
Made to order
· Lead time: configured to order — request a build slot. Installation, training and process support included from California.
Compact open-parameter ceramic SLA printer for research and material development — a 3.9×3.9×5.9 in / 100×100×150 mm build that starts a print from as little as 60 mL of ceramic. Develop your own process, then scale the same technology to 3DCeram production systems. Full print → debind → sinter workflow supported by Additive Plus.
- Open parameters — qualify new ceramics & formulations, not just vendor recipes.
- Print from 60 mL — 10 mL with SAM option · change ceramic in ~20 min.
- Lead time: configured to order — install, training & scale-up support from California.
Made to order
· Lead time: configured to order — request a build slot. Installation, training and process support included from California.
Multi-material ceramic SLA printer that prints two materials in the same layer — ceramic plus a second ceramic, metal or polymer — on a 3.9×3.9×5.9 in / 100×100×150 mm platform. It makes functionally graded and multi-material ceramic parts single-material printing can't. Full print → debind → co-sinter workflow supported by Additive Plus.
- Two materials in one layer — ceramic + ceramic, metal or polymer.
- Open-parameter R&D — 100×100×150 mm build, cartridges from 60 mL.
- Lead time: configured to order — material-pair & co-sinter support from California.
Made to order
· Lead time: configured to order — request a build slot. Installation, training and process support included from California.
Production-scale multi-material ceramic SLA system: alongside the base ceramic it deposits up to three additional materials in one part, via dispensers from needle valve to micro-distribution, all in CPS 2.0. On an 11.8×11.8×3.9 in / 300×300×100 mm platform with a fine 35 µm UV laser. Full print → debind → co-sinter workflow supported by Additive Plus.
- Up to 4 materials in one part — base ceramic + 3 dispensed materials.
- Fine 35 µm UV laser — 355 nm, detail across the 300×300 mm platform.
- Lead time: configured to order — material-set & co-sinter support from California.
Made to order
· Lead time: configured to order — request a build slot. Installation, training and process support included from California.
Print near-zero-expansion cordierite parts on 3DCeram's Ceramaker laser-SLA platform, then debind and sinter to a dimensionally stable oxide ceramic.
- ✓ Coefficient of thermal expansion near zero — dimensional stability through thermal cycling
- ✓ Aerospace optics, metrology and vacuum hardware; >98% dense after sintering
- ✓ Ceramic SLA paste for the 3DCeram Ceramaker platform — quote-based, mutual NDA before spec review
Made to order
· Made to order by 3DCeram in France — lead time confirmed with your quote.Not sure which system fits?
Tell us your application. We'll send our top recommendation.
Browse all categories
Printers, materials, print services and lab equipment — including AO Metal, the LPBF printer we design and build ourselves.
Have a CAD? Have a quote in 24h.
Upload your file or talk to an engineer — no obligation, no spam, NDA on request. First-time customers get free DfAM review.